Highly elastic fixing adhesive mixture — ТМ 25 WHITE

Field of application:

For laying all types of ceramic and clinker tiles, as well as natural stone indoors and outdoors, on walls and floors, in dry and wet areas. For facing with large-format tiles 1200*600 mm, with moisture absorption less than 0.5%. Especially suitable for heated floors and thin translucent plates, glass mosaic, light marble, etc., for facing stairs and stairwells, as well as surfaces, subject to intense mechanical deformations. Effective on foundations, subject to periodic deformation due to moisture and extension(indoor pools and tanks, showers, balconies, terraces, heated floors, etc.), on terraces and balconies.

Features:

for dry and wet rooms;
water resistance and frost resistance;
withstands internal mechanical deformation;
high fixing capacity;
highly elastic for wide-format tiles;
excellent adhesion to old alkyd bases;
for covering floors with water and electric heating

Advantages:

from 20 min

Open time

For white cement

Vapor permeable

Impact resistant

More about the product

Specifications

Storage	Cement, mineral fillers, polymer modifiers
Water consumption for 25 kg dry mixture, l	7.0....7.5
Consumption of dry mixture per 1 m² with a layer thickness of 1 mm	Approximately 1.7 kg
Expiry date, min	At least 60
Open time, min	At least 20
Adjustment time, min	At least 10
Adhesion strength to the base after: aging in air-dry conditions, MPa	Not less than 1.0
Coarseness of aggregate, mm	Not more than 0.63
Displacement of the material to be fixed (only for walls), mm	Not more than 0.5
Compressive strength (after 28 days), Mpa	Not less than 10.0
Application temperature	From +5 ⁰С to +30 ⁰С
Operating temperature	From -30 ⁰С to +40 ⁰С
The time of possible technological movement, hours	Not before 48

Preparation of the base

The foundation is prepared in accordance with DSTU-NB A.3.1- 23:2013 and DSTU-NB V.2.6-212:2016. The surface of the base must be dry, strong, even, with low and uniform water absorption. Before applying the dry mixture, the surface is cleaned of dust, oil stains and other substances that reduce adhesion. Surfaces made of porous concrete, as well as gypsum and smooth concrete surfaces should be treated with a primer. Leave primed surfaces for at least 4 hours before starting cladding.
Preparation of the solution

Preparation of mortar mixture: pour water into a clean container (water temperature from +15 °C to +25 °C) at the rate of 0.28-0.30 l (l) per 1 kg (kg) of dry mixture (7.0-7 .5 l (l) per 25 kg (kg)), gradually add the dry mixture and mix with a low-speed mixer until a homogeneous mass without lumps is obtained. After 5 minutes mix again.
Recommendations

The use of dry mixture is recommended at temperatures from +5 °C to +30 °C and relative air humidity not higher than 65%. Eyes and skin should be protected during work. If the mixture gets into the eyes, it is necessary to immediately wash them with water and consult a doctor.

On bases with deformation seams, the latter must be additionally duplicated in the facing, followed by their filling with elastic sealants. When performing external work, a combined method is used for fixing tiles: the mortar mixture is applied to the surface in a layer, the thickness of which should correspond to the size of the grater tooth, and to the tile in a layer of up to 1 mm, evenly over the entire surface.

Execution of works

The mortar mixture is applied in a thin layer to the prepared base using a metal spatula or grater and smoothed with a toothed spatula. At one time, such amount of solution is applied that can be used within 15 minutes. The tile was not previously repl
Packaging

Paper bags with an inner polyethylene layer of 25 kg.
Storage

The mixture must be stored in a branded sealed package in a dry room, on pallets. The shelf life is 12 months from the date of manufacture indicated on the package.
Cost

On average, 1.7 kg of glue is used per 1 m², depending on the thickness of the applied layer and the condition of the surface.