Adhesive mixture for facing fireplaces, stoves and "warm" floors — TM 21 THERMO
External and internal
Field of application:
For leveling concrete bases and floor screeds on a mineral basis, followed by facing with ceramic coatings, as well as coatings made of linoleum, etc. inside residential and civil premises, screed leveling with heating elements (heated floor). It can be used in the form of a monolithic-combined floor, a monolithic floor on a split layer, a monolithic "floating" floor. The recommended layer thickness is from 3 mm to 50 mm.
Features:
Advantages:
Storage |
Made on the basis of a mixture of mineral binders, fillers and functional additives, reinforced with microfibers |
Water consumption per 25 kg of dry mixture |
4.0-4.5 l |
Consumption of dry mixture per 1m² with a layer thickness of 1 mm |
Approximately 1.75 kg |
Expiry date, min | At least 30 |
Readiness for initial loads | In 8 hours |
The possibility of laying ceramic and stone tiles, not earlier |
After 72 hours |
Laying carpets, PVC, linoleum, parquet |
After 7 days |
Adhesion strength to the concrete base after endurance in air-dry conditions, MPa |
Not less than 1.0 |
Compressive strength limit after 28 days, MPa |
At least 20 |
Bending tensile strength after 28 days, MPa | At least 4.0 |
Coarseness of aggregate, mm | Not more than 0.63 |
Application temperature | From +5 ⁰С to +30 ⁰С |
Operating temperature | From -30 ⁰С to +70 ⁰С |
When preparing the base, it is necessary to comply with the requirements of DSTU-N B A.3.1-23:2013, DSTU-N B V.2.6-212:2016 and SNiP 2.03.13-88. The base must be load-bearing and strong, cleaned of dust, dirt, lime, oils, fats, wax, paint. To create a clean contact layer, it is necessary to clean the base from dust using a household or industrial vacuum cleaner. Weak layers should be removed, existing cracks should be widened, primed and filled with FL 50 mixture. Surfaces that strongly absorb liquid should be treated with a deep penetration primer and allowed to stand for at least 4 hours. Weakly absorbent surfaces should be treated with an acrylic primer and left for at least 4 hours. It is necessary to separate the monolithic floor from the walls and columns with a thin elastic layer (for example, thin strips of polystyrene foam).
Pour the dry mixture into a container with clean water at room temperature in the proportion: 0.18 l per 1 kg of the mixture (4.5 l per 25 kg bag). Mix with a drill with a nozzle (manual pouring) or a pressure mixer (machine pouring) until a homogeneous state. After that, keep the solution for 5 minutes and mix thoroughly again. With each new mixing of the mixture, it is necessary to control the mixing time (approximately 6 minutes) and the consistency of the solution. The solution can be used within 30 minutes from the moment of preparation. Use clean containers and tools for cooking.
During the hardening of the monolithic floor in the first two days, it must be protected from direct sunlight and drafts, as well as provide adequate ventilation. During operation, the base should not be exposed to moisture. Work must be performed at an air temperature of +5°С to +30°С. The most effective result is achieved at a temperature of +20°С and a relative humidity of 60%. In other conditions, the working parameters of the mixture may change. In the case of using the mixture in non-standard conditions or for other purposes, it is necessary to conduct tests yourself or consult with the manufacturer. The manufacturer is not responsible for improper use of the material, as well as its use for other purposes and conditions not provided for in the technical description. Floor mixture FL 50 contains cement, which causes an alkaline reaction at the moment of hydration, so it is necessary to protect eyes and skin when working. If the solution mixture gets into the eyes, they should be immediately washed with running water and consult a doctor. An excess amount of water causes delamination of the solution, increases the time it takes for the mixture to harden, and reduces the quality of the coating.
Before carrying out work, it is necessary to determine the future thickness of the layer. The marked technological area is filled with the mixture, starting from the furthest corner. The poured mixture is immediately deaerated (removed air) using a nee
Paper bags with an inner polyethylene layer of 25 kg.
The mixture must be stored in the company's airtight packaging in a dry room, on pallets. The shelf life is 12 months from the date of manufacture indicated on the package.
The average consumption of the mixture per 1 mm of layer thickness is 1.75 kg/m2.